diff options
Diffstat (limited to 'source/url.go')
0 files changed, 0 insertions, 0 deletions
 |
index : ddnnss | |
| dynamic domain no-name system service |
| summaryrefslogtreecommitdiff |
# To create the Firmware you need to use the following configuration:
# - Micro-controller: STM32
# - Processor model: STM32F103
# - Bootloader offset: 32KiB
# - Communication interface: Serial (on USART1 PA10/PA9)
#
# To install the Firmware rename the klipper bin to `main_board_20xxxxxx.bin`
# and copy it to an SD Card.
# Power off the Printer, insert the SD Card and power it on.
# It should beep several times and the LCD should be stuck on the Splash screen.
# Now you should be able to connect to the Printer, you might need to change
# the mcu/serial setting in this config according to your set up.
#
# If you want to revert the Firmware back to Marlin you simply need to flash it
# with a anycubic firmware through the SD Card
# note: this config is a modified version of the Anycubic Vyper configuration
# from the main Klipper repository.
# the default configuration does NOT work, so i've tried adjusting it with
# other values found in any repository i could find which has one.
# see:
# - https://github.com/Klipper3d/klipper/blob/master/config/printer-anycubic-vyper-2021.cfg
# - https://github.com/xmtrcv/vyper-klipper/printer.cfg
[stepper_x]
step_pin: PC2
dir_pin: PB9
enable_pin: !PC3
microsteps: 16
rotation_distance: 40
endstop_pin: !PA7
position_min: -3
position_endstop: -3
position_max: 245
homing_speed: 30.0
[stepper_y]
step_pin: PB8
dir_pin: PB7
enable_pin: !PC13
microsteps: 16
rotation_distance: 32
endstop_pin: !PC5
position_min: -10
position_endstop: -10
position_max: 245
homing_speed: 30.0
[stepper_z]
step_pin: PB6
dir_pin: !PB5
enable_pin: !PC14
microsteps: 16
rotation_distance: 8
endstop_pin: PB2
position_endstop: -1.600
position_max: 250
position_min: -3
homing_speed: 5.0
[stepper_z1]
step_pin: PC0
dir_pin: !PC1
enable_pin: !PC15
microsteps: 16
rotation_distance: 8
endstop_pin: PC6
[extruder]
step_pin: PB4
dir_pin: !PB3
enable_pin: !PA15
microsteps: 16
rotation_distance: 21.807 #has to be calibrated by everyone, official document: diameter = 7.25
gear_ratio: 50:17
full_steps_per_rotation: 200
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: PA1
sensor_type: ATC Semitec 104GT-2
sensor_pin: PC4
max_extrude_cross_section: 50.0
max_extrude_only_distance: 500
control: pid
pid_kp: 28.347
pid_ki: 1.588
pid_kd: 126.496
min_temp: 0
max_temp: 260
[heater_fan extruder_fan]
pin: PB1
[heater_bed]
heater_pin: PA4
sensor_type: EPCOS 100K B57560G104F
sensor_pin: PB0
control: pid
pid_kp: 68.259
pid_ki: 1.058
pid_kd: 1100.678
min_temp: 0
max_temp: 110
[fan]
pin: PA0
[temperature_fan Mainboard]
pin: mcu:PA14
sensor_type: temperature_mcu
max_power: 1.0
shutdown_speed: 1.0
hardware_pwm: false
kick_start_time: 0.5
off_below: 0.4
max_temp: 100
min_temp: 20
target_temp: 50
max_speed: 1.0
min_speed: 0.3
control: pid
pid_Kp: 1
pid_Ki: 1
pid_Kd: 1
# [probe]
# pin: !PB12
# z_offset: -0.150
# speed: 1
# samples: 1
# activate_gcode:
# PROBE_RESET
[output_pin beeper_pin]
pin: PB15
pwm: True
value: 0
shutdown_value: 0
cycle_time: 0.001
# [output_pin PROBE_RESET_PIN]
# pin: PB13
[output_pin led_pin]
pin: mcu:PA13
pwm: False
value: 0
[bed_mesh]
speed: 50
horizontal_move_z: 5
mesh_min: 15, 15
mesh_max: 230, 230
probe_count: 7, 7
mesh_pps: 2, 3
algorithm: bicubic
fade_end: 10.0
[filament_switch_sensor runout]
pause_on_runout: True
switch_pin: PA5
[temperature_sensor Raspberry_Pi_4]
sensor_type: temperature_host
min_temp: 0
max_temp: 100
[mcu]
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
restart_method: command
[safe_z_home]
home_xy_position: -3,-7
z_hop: 10
[printer]
kinematics: cartesian
max_velocity: 150
max_accel: 1500
minimum_cruise_ratio: 0
max_z_velocity: 5
max_z_accel: 100
# [gcode_macro PROBE_RESET]
# gcode:
# SET_PIN PIN=PROBE_RESET_PIN VALUE=0
# G4 P300
# SET_PIN PIN=PROBE_RESET_PIN VALUE=1
# G4 P100