diff options
Diffstat (limited to 'assets')
| -rw-r--r-- | assets/printer/firmware.cfg | 110 | ||||
| -rw-r--r-- | assets/printer/mainsail.cfg | 313 | ||||
| -rw-r--r-- | assets/printer/printer.cfg | 159 |
3 files changed, 582 insertions, 0 deletions
diff --git a/assets/printer/firmware.cfg b/assets/printer/firmware.cfg new file mode 100644 index 0000000..dd5a878 --- /dev/null +++ b/assets/printer/firmware.cfg @@ -0,0 +1,110 @@ +CONFIG_LOW_LEVEL_OPTIONS=y +# CONFIG_MACH_AVR is not set +# CONFIG_MACH_ATSAM is not set +# CONFIG_MACH_ATSAMD is not set +# CONFIG_MACH_LPC176X is not set +CONFIG_MACH_STM32=y +# CONFIG_MACH_HC32F460 is not set +# CONFIG_MACH_RP2040 is not set +# CONFIG_MACH_PRU is not set +# CONFIG_MACH_AR100 is not set +# CONFIG_MACH_LINUX is not set +# CONFIG_MACH_SIMU is not set +CONFIG_BOARD_DIRECTORY="stm32" +CONFIG_MCU="stm32f103xe" +CONFIG_CLOCK_FREQ=72000000 +CONFIG_SERIAL=y +CONFIG_FLASH_SIZE=0x10000 +CONFIG_FLASH_BOOT_ADDRESS=0x8000000 +CONFIG_RAM_START=0x20000000 +CONFIG_RAM_SIZE=0x5000 +CONFIG_STACK_SIZE=512 +CONFIG_FLASH_APPLICATION_ADDRESS=0x8008000 +CONFIG_STM32_SELECT=y +CONFIG_MACH_STM32F103=y +# CONFIG_MACH_STM32F207 is not set +# CONFIG_MACH_STM32F401 is not set +# CONFIG_MACH_STM32F405 is not set +# CONFIG_MACH_STM32F407 is not set +# CONFIG_MACH_STM32F429 is not set +# CONFIG_MACH_STM32F446 is not set +# CONFIG_MACH_STM32F765 is not set +# CONFIG_MACH_STM32F031 is not set +# CONFIG_MACH_STM32F042 is not set +# CONFIG_MACH_STM32F070 is not set +# CONFIG_MACH_STM32F072 is not set +# CONFIG_MACH_STM32G070 is not set +# CONFIG_MACH_STM32G071 is not set +# CONFIG_MACH_STM32G0B0 is not set +# CONFIG_MACH_STM32G0B1 is not set +# CONFIG_MACH_STM32G431 is not set +# CONFIG_MACH_STM32G474 is not set +# CONFIG_MACH_STM32H723 is not set +# CONFIG_MACH_STM32H743 is not set +# CONFIG_MACH_STM32H750 is not set +# CONFIG_MACH_STM32L412 is not set +# CONFIG_MACH_N32G452 is not set +# CONFIG_MACH_N32G455 is not set +# CONFIG_MACH_STM32F103x6 is not set +CONFIG_MACH_STM32F1=y +CONFIG_HAVE_STM32_USBFS=y +CONFIG_HAVE_STM32_CANBUS=y +CONFIG_STM32F103GD_DISABLE_SWD=y +CONFIG_STM32_DFU_ROM_ADDRESS=0 +# CONFIG_STM32_FLASH_START_2000 is not set +# CONFIG_STM32_FLASH_START_5000 is not set +# CONFIG_STM32_FLASH_START_7000 is not set +CONFIG_STM32_FLASH_START_8000=y +# CONFIG_STM32_FLASH_START_8800 is not set +# CONFIG_STM32_FLASH_START_9000 is not set +# CONFIG_STM32_FLASH_START_10000 is not set +# CONFIG_STM32_FLASH_START_800 is not set +# CONFIG_STM32_FLASH_START_1000 is not set +# CONFIG_STM32_FLASH_START_4000 is not set +# CONFIG_STM32_FLASH_START_0000 is not set +CONFIG_STM32_CLOCK_REF_8M=y +# CONFIG_STM32_CLOCK_REF_12M is not set +# CONFIG_STM32_CLOCK_REF_16M is not set +# CONFIG_STM32_CLOCK_REF_20M is not set +# CONFIG_STM32_CLOCK_REF_24M is not set +# CONFIG_STM32_CLOCK_REF_25M is not set +# CONFIG_STM32_CLOCK_REF_INTERNAL is not set +CONFIG_CLOCK_REF_FREQ=8000000 +CONFIG_STM32F0_TRIM=16 +# CONFIG_STM32_USB_PA11_PA12 is not set +CONFIG_STM32_SERIAL_USART1=y +# CONFIG_STM32_SERIAL_USART1_ALT_PB7_PB6 is not set +# CONFIG_STM32_SERIAL_USART2 is not set +# CONFIG_STM32_SERIAL_USART2_ALT_PD6_PD5 is not set +# CONFIG_STM32_SERIAL_USART3 is not set +# CONFIG_STM32_SERIAL_USART3_ALT_PD9_PD8 is not set +# CONFIG_STM32_CANBUS_PA11_PA12 is not set +# CONFIG_STM32_CANBUS_PA11_PB9 is not set +# CONFIG_STM32_MMENU_CANBUS_PB8_PB9 is not set +# CONFIG_STM32_MMENU_CANBUS_PD0_PD1 is not set +CONFIG_SERIAL_BAUD=250000 +CONFIG_USB_VENDOR_ID=0x1d50 +CONFIG_USB_DEVICE_ID=0x614e +CONFIG_USB_SERIAL_NUMBER="12345" +CONFIG_WANT_GPIO_BITBANGING=y +CONFIG_WANT_DISPLAYS=y +CONFIG_WANT_SENSORS=y +CONFIG_WANT_LIS2DW=y +CONFIG_WANT_LDC1612=y +CONFIG_WANT_HX71X=y +CONFIG_WANT_ADS1220=y +CONFIG_WANT_SOFTWARE_I2C=y +CONFIG_WANT_SOFTWARE_SPI=y +CONFIG_NEED_SENSOR_BULK=y +CONFIG_CANBUS_FREQUENCY=1000000 +CONFIG_INITIAL_PINS="" +CONFIG_HAVE_GPIO=y +CONFIG_HAVE_GPIO_ADC=y +CONFIG_HAVE_GPIO_SPI=y +CONFIG_HAVE_GPIO_I2C=y +CONFIG_HAVE_GPIO_HARD_PWM=y +CONFIG_HAVE_STRICT_TIMING=y +CONFIG_HAVE_CHIPID=y +CONFIG_HAVE_STEPPER_BOTH_EDGE=y +CONFIG_HAVE_BOOTLOADER_REQUEST=y +CONFIG_INLINE_STEPPER_HACK=y diff --git a/assets/printer/mainsail.cfg b/assets/printer/mainsail.cfg new file mode 100644 index 0000000..201a6c2 --- /dev/null +++ b/assets/printer/mainsail.cfg @@ -0,0 +1,313 @@ +## Client klipper macro definitions +## +## Copyright (C) 2022 Alex Zellner <alexander.zellner@googlemail.com> +## +## This file may be distributed under the terms of the GNU GPLv3 license +## +## !!! This file is read-only. Maybe the used editor indicates that. !!! +## +## Customization: +## 1) copy the gcode_macro _CLIENT_VARIABLE (see below) to your printer.cfg +## 2) remove the comment mark (#) from all lines +## 3) change any value in there to your needs +## +## Use the PAUSE macro direct in your M600: +## e.g. with a different park position front left and a minimal height of 50 +## [gcode_macro M600] +## description: Filament change +## gcode: PAUSE X=10 Y=10 Z_MIN=50 +## Z_MIN will park the toolhead at a minimum of 50 mm above to bed to make it easier for you to swap filament. +## +## Client variable macro for your printer.cfg +#[gcode_macro _CLIENT_VARIABLE] +#variable_use_custom_pos : False ; use custom park coordinates for x,y [True/False] +#variable_custom_park_x : 0.0 ; custom x position; value must be within your defined min and max of X +#variable_custom_park_y : 0.0 ; custom y position; value must be within your defined min and max of Y +#variable_custom_park_dz : 2.0 ; custom dz value; the value in mm to lift the nozzle when move to park position +#variable_retract : 1.0 ; the value to retract while PAUSE +#variable_cancel_retract : 5.0 ; the value to retract while CANCEL_PRINT +#variable_speed_retract : 35.0 ; retract speed in mm/s +#variable_unretract : 1.0 ; the value to unretract while RESUME +#variable_speed_unretract : 35.0 ; unretract speed in mm/s +#variable_speed_hop : 15.0 ; z move speed in mm/s +#variable_speed_move : 100.0 ; move speed in mm/s +#variable_park_at_cancel : False ; allow to move the toolhead to park while execute CANCEL_PRINT [True/False] +#variable_park_at_cancel_x : None ; different park position during CANCEL_PRINT [None/Position as Float]; park_at_cancel must be True +#variable_park_at_cancel_y : None ; different park position during CANCEL_PRINT [None/Position as Float]; park_at_cancel must be True +## !!! Caution [firmware_retraction] must be defined in the printer.cfg if you set use_fw_retract: True !!! +#variable_use_fw_retract : False ; use fw_retraction instead of the manual version [True/False] +#variable_idle_timeout : 0 ; time in sec until idle_timeout kicks in. Value 0 means that no value will be set or restored +#variable_runout_sensor : "" ; If a sensor is defined, it will be used to cancel the execution of RESUME in case no filament is detected. +## Specify the config name of the runout sensor e.g "filament_switch_sensor runout". Hint use the same as in your printer.cfg +## !!! Custom macros, please use with care and review the section of the corresponding macro. +## These macros are for simple operations like setting a status LED. Please make sure your macro does not interfere with the basic macro functions. +## Only single line commands are supported, please create a macro if you need more than one command. +#variable_user_pause_macro : "" ; Everything inside the "" will be executed after the klipper base pause (PAUSE_BASE) function +#variable_user_resume_macro: "" ; Everything inside the "" will be executed before the klipper base resume (RESUME_BASE) function +#variable_user_cancel_macro: "" ; Everything inside the "" will be executed before the klipper base cancel (CANCEL_PRINT_BASE) function +#gcode: + +[virtual_sdcard] +path: /srv/klipper/gcodes +on_error_gcode: CANCEL_PRINT + +[pause_resume] +#recover_velocity: 50. +# When capture/restore is enabled, the speed at which to return to +# the captured position (in mm/s). Default is 50.0 mm/s. + +[display_status] + +[respond] + +[gcode_macro CANCEL_PRINT] +description: Cancel the actual running print +rename_existing: CANCEL_PRINT_BASE +gcode: + ##### get user parameters or use default ##### + {% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %} + {% set allow_park = client.park_at_cancel|default(false)|lower == 'true' %} + {% set retract = client.cancel_retract|default(5.0)|abs %} + ##### define park position ##### + {% set park_x = "" if (client.park_at_cancel_x|default(none) is none) + else "X=" ~ client.park_at_cancel_x %} + {% set park_y = "" if (client.park_at_cancel_y|default(none) is none) + else "Y=" ~ client.park_at_cancel_y %} + {% set custom_park = park_x|length > 0 or park_y|length > 0 %} + ##### end of definitions ##### + # restore idle_timeout time if needed + {% if printer['gcode_macro RESUME'].restore_idle_timeout > 0 %} + SET_IDLE_TIMEOUT TIMEOUT={printer['gcode_macro RESUME'].restore_idle_timeout} + {% endif %} + {% if (custom_park or not printer.pause_resume.is_paused) and allow_park %} _TOOLHEAD_PARK_PAUSE_CANCEL {park_x} {park_y} {% endif %} + _CLIENT_RETRACT LENGTH={retract} + TURN_OFF_HEATERS + M106 S0 + {client.user_cancel_macro|default("")} + SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=idle_state VALUE=False + # clear pause_next_layer and pause_at_layer as preparation for next print + SET_PAUSE_NEXT_LAYER ENABLE=0 + SET_PAUSE_AT_LAYER ENABLE=0 LAYER=0 + CANCEL_PRINT_BASE + +[gcode_macro PAUSE] +description: Pause the actual running print +rename_existing: PAUSE_BASE +gcode: + ##### get user parameters or use default ##### + {% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %} + {% set idle_timeout = client.idle_timeout|default(0) %} + {% set temp = printer[printer.toolhead.extruder].target if printer.toolhead.extruder != '' else 0 %} + {% set restore = False if printer.toolhead.extruder == '' + else True if params.RESTORE|default(1)|int == 1 else False %} + ##### end of definitions ##### + SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=last_extruder_temp VALUE="{{'restore': restore, 'temp': temp}}" + # set a new idle_timeout value + {% if idle_timeout > 0 %} + SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=restore_idle_timeout VALUE={printer.configfile.settings.idle_timeout.timeout} + SET_IDLE_TIMEOUT TIMEOUT={idle_timeout} + {% endif %} + PAUSE_BASE + {client.user_pause_macro|default("")} + _TOOLHEAD_PARK_PAUSE_CANCEL {rawparams} + +[gcode_macro RESUME] +description: Resume the actual running print +rename_existing: RESUME_BASE +variable_last_extruder_temp: {'restore': False, 'temp': 0} +variable_restore_idle_timeout: 0 +variable_idle_state: False +gcode: + ##### get user parameters or use default ##### + {% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %} + {% set velocity = printer.configfile.settings.pause_resume.recover_velocity %} + {% set sp_move = client.speed_move|default(velocity) %} + {% set runout_resume = True if client.runout_sensor|default("") == "" # no runout + else True if not printer[client.runout_sensor].enabled # sensor is disabled + else printer[client.runout_sensor].filament_detected %} # sensor status + {% set can_extrude = True if printer.toolhead.extruder == '' # no extruder defined in config + else printer[printer.toolhead.extruder].can_extrude %} # status of active extruder + {% set do_resume = False %} + {% set prompt_txt = [] %} + ##### end of definitions ##### + #### Printer comming from timeout idle state #### + {% if printer.idle_timeout.state|upper == "IDLE" or idle_state %} + SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=idle_state VALUE=False + {% if last_extruder_temp.restore %} + # we need to use the unicode (\u00B0) for the ° as py2 env's would throw an error otherwise + RESPOND TYPE=echo MSG='{"Restoring \"%s\" temperature to %3.1f\u00B0C, this may take some time" % (printer.toolhead.extruder, last_extruder_temp.temp) }' + M109 S{last_extruder_temp.temp} + {% set do_resume = True %} + {% elif can_extrude %} + {% set do_resume = True %} + {% else %} + RESPOND TYPE=error MSG='{"Resume aborted !!! \"%s\" not hot enough, please heat up again and press RESUME" % printer.toolhead.extruder}' + {% set _d = prompt_txt.append("\"%s\" not hot enough, please heat up again and press RESUME" % printer.toolhead.extruder) %} + {% endif %} + #### Printer comming out of regular PAUSE state #### + {% elif can_extrude %} + {% set do_resume = True %} + {% else %} + RESPOND TYPE=error MSG='{"Resume aborted !!! \"%s\" not hot enough, please heat up again and press RESUME" % printer.toolhead.extruder}' + {% set _d = prompt_txt.append("\"%s\" not hot enough, please heat up again and press RESUME" % printer.toolhead.extruder) %} + {% endif %} + {% if runout_resume %} + {% if do_resume %} + {% if restore_idle_timeout > 0 %} SET_IDLE_TIMEOUT TIMEOUT={restore_idle_timeout} {% endif %} # restore idle_timeout time + {client.user_resume_macro|default("")} + _CLIENT_EXTRUDE + RESUME_BASE VELOCITY={params.VELOCITY|default(sp_move)} + {% endif %} + {% else %} + RESPOND TYPE=error MSG='{"Resume aborted !!! \"%s\" detects no filament, please load filament and press RESUME" % (client.runout_sensor.split(" "))[1]}' + {% set _d = prompt_txt.append("\"%s\" detects no filament, please load filament and press RESUME" % (client.runout_sensor.split(" "))[1]) %} + {% endif %} + ##### Generate User Information box in case of abort ##### + {% if not (runout_resume and do_resume) %} + RESPOND TYPE=command MSG="action:prompt_begin RESUME aborted !!!" + {% for element in prompt_txt %} + RESPOND TYPE=command MSG='{"action:prompt_text %s" % element}' + {% endfor %} + RESPOND TYPE=command MSG="action:prompt_footer_button Ok|RESPOND TYPE=command MSG=action:prompt_end|info" + RESPOND TYPE=command MSG="action:prompt_show" + {% endif %} + +# Usage: SET_PAUSE_NEXT_LAYER [ENABLE=[0|1]] [MACRO=<name>] +[gcode_macro SET_PAUSE_NEXT_LAYER] +description: Enable a pause if the next layer is reached +gcode: + {% set pause_next_layer = printer['gcode_macro SET_PRINT_STATS_INFO'].pause_next_layer %} + {% set ENABLE = params.ENABLE|default(1)|int != 0 %} + {% set MACRO = params.MACRO|default(pause_next_layer.call, True) %} + SET_GCODE_VARIABLE MACRO=SET_PRINT_STATS_INFO VARIABLE=pause_next_layer VALUE="{{ 'enable': ENABLE, 'call': MACRO }}" + +# Usage: SET_PAUSE_AT_LAYER [ENABLE=[0|1]] [LAYER=<number>] [MACRO=<name>] +[gcode_macro SET_PAUSE_AT_LAYER] +description: Enable/disable a pause if a given layer number is reached +gcode: + {% set pause_at_layer = printer['gcode_macro SET_PRINT_STATS_INFO'].pause_at_layer %} + {% set ENABLE = params.ENABLE|int != 0 if params.ENABLE is defined + else params.LAYER is defined %} + {% set LAYER = params.LAYER|default(pause_at_layer.layer)|int %} + {% set MACRO = params.MACRO|default(pause_at_layer.call, True) %} + SET_GCODE_VARIABLE MACRO=SET_PRINT_STATS_INFO VARIABLE=pause_at_layer VALUE="{{ 'enable': ENABLE, 'layer': LAYER, 'call': MACRO }}" + +# Usage: SET_PRINT_STATS_INFO [TOTAL_LAYER=<total_layer_count>] [CURRENT_LAYER= <current_layer>] +[gcode_macro SET_PRINT_STATS_INFO] +rename_existing: SET_PRINT_STATS_INFO_BASE +description: Overwrite, to get pause_next_layer and pause_at_layer feature +variable_pause_next_layer: { 'enable': False, 'call': "PAUSE" } +variable_pause_at_layer : { 'enable': False, 'layer': 0, 'call': "PAUSE" } +gcode: + {% if pause_next_layer.enable %} + RESPOND TYPE=echo MSG='{"%s, forced by pause_next_layer" % pause_next_layer.call}' + {pause_next_layer.call} ; execute the given gcode to pause, should be either M600 or PAUSE + SET_PAUSE_NEXT_LAYER ENABLE=0 + {% elif pause_at_layer.enable and params.CURRENT_LAYER is defined and params.CURRENT_LAYER|int == pause_at_layer.layer %} + RESPOND TYPE=echo MSG='{"%s, forced by pause_at_layer [%d]" % (pause_at_layer.call, pause_at_layer.layer)}' + {pause_at_layer.call} ; execute the given gcode to pause, should be either M600 or PAUSE + SET_PAUSE_AT_LAYER ENABLE=0 + {% endif %} + SET_PRINT_STATS_INFO_BASE {rawparams} + +##### internal use ##### +[gcode_macro _TOOLHEAD_PARK_PAUSE_CANCEL] +description: Helper: park toolhead used in PAUSE and CANCEL_PRINT +gcode: + ##### get user parameters or use default ##### + {% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %} + {% set velocity = printer.configfile.settings.pause_resume.recover_velocity %} + {% set use_custom = client.use_custom_pos|default(false)|lower == 'true' %} + {% set custom_park_x = client.custom_park_x|default(0.0) %} + {% set custom_park_y = client.custom_park_y|default(0.0) %} + {% set park_dz = client.custom_park_dz|default(2.0)|abs %} + {% set sp_hop = client.speed_hop|default(15) * 60 %} + {% set sp_move = client.speed_move|default(velocity) * 60 %} + ##### get config and toolhead values ##### + {% set origin = printer.gcode_move.homing_origin %} + {% set act = printer.gcode_move.gcode_position %} + {% set max = printer.toolhead.axis_maximum %} + {% set cone = printer.toolhead.cone_start_z|default(max.z) %} ; height as long the toolhead can reach max and min of an delta + {% set round_bed = True if printer.configfile.settings.printer.kinematics is in ['delta','polar','rotary_delta','winch'] + else False %} + ##### define park position ##### + {% set z_min = params.Z_MIN|default(0)|float %} + {% set z_park = [[(act.z + park_dz), z_min]|max, (max.z - origin.z)]|min %} + {% set x_park = params.X if params.X is defined + else custom_park_x if use_custom + else 0.0 if round_bed + else (max.x - 5.0) %} + {% set y_park = params.Y if params.Y is defined + else custom_park_y if use_custom + else (max.y - 5.0) if round_bed and z_park < cone + else 0.0 if round_bed + else (max.y - 5.0) %} + ##### end of definitions ##### + _CLIENT_RETRACT + {% if "xyz" in printer.toolhead.homed_axes %} + G90 + G1 Z{z_park} F{sp_hop} + G1 X{x_park} Y{y_park} F{sp_move} + {% if not printer.gcode_move.absolute_coordinates %} G91 {% endif %} + {% else %} + RESPOND TYPE=echo MSG='Printer not homed' + {% endif %} + +[gcode_macro _CLIENT_EXTRUDE] +description: Extrudes, if the extruder is hot enough +gcode: + ##### get user parameters or use default ##### + {% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %} + {% set use_fw_retract = (client.use_fw_retract|default(false)|lower == 'true') and (printer.firmware_retraction is defined) %} + {% set length = params.LENGTH|default(client.unretract)|default(1.0)|float %} + {% set speed = params.SPEED|default(client.speed_unretract)|default(35) %} + {% set absolute_extrude = printer.gcode_move.absolute_extrude %} + ##### end of definitions ##### + {% if printer.toolhead.extruder != '' %} + {% if printer[printer.toolhead.extruder].can_extrude %} + {% if use_fw_retract %} + {% if length < 0 %} + G10 + {% else %} + G11 + {% endif %} + {% else %} + M83 + G1 E{length} F{(speed|float|abs) * 60} + {% if absolute_extrude %} + M82 + {% endif %} + {% endif %} + {% else %} + RESPOND TYPE=echo MSG='{"\"%s\" not hot enough" % printer.toolhead.extruder}' + {% endif %} + {% endif %} + +[gcode_macro _CLIENT_RETRACT] +description: Retracts, if the extruder is hot enough +gcode: + {% set client = printer['gcode_macro _CLIENT_VARIABLE']|default({}) %} + {% set length = params.LENGTH|default(client.retract)|default(1.0)|float %} + {% set speed = params.SPEED|default(client.speed_retract)|default(35) %} + + _CLIENT_EXTRUDE LENGTH=-{length|float|abs} SPEED={speed|float|abs} + +[gcode_macro _CLIENT_LINEAR_MOVE] +description: Linear move with save and restore of the gcode state +gcode: + {% set x_move = "X" ~ params.X if params.X is defined else "" %} + {% set y_move = "Y" ~ params.Y if params.Y is defined else "" %} + {% set z_move = "Z" ~ params.Z if params.Z is defined else "" %} + {% set e_move = "E" ~ params.E if params.E is defined else "" %} + {% set rate = "F" ~ params.F if params.F is defined else "" %} + {% set ABSOLUTE = params.ABSOLUTE | default(0) | int != 0 %} + {% set ABSOLUTE_E = params.ABSOLUTE_E | default(0) | int != 0 %} + SAVE_GCODE_STATE NAME=_client_movement + {% if x_move or y_move or z_move %} + G9{ 0 if ABSOLUTE else 1 } + {% endif %} + {% if e_move %} + M8{ 2 if ABSOLUTE_E else 3 } + {% endif %} + G1 { x_move } { y_move } { z_move } { e_move } { rate } + RESTORE_GCODE_STATE NAME=_client_movement diff --git a/assets/printer/printer.cfg b/assets/printer/printer.cfg new file mode 100644 index 0000000..a98cb2b --- /dev/null +++ b/assets/printer/printer.cfg @@ -0,0 +1,159 @@ +# This file contains a configuration for the Anycubic Vyper printer from 2021. +# It uses a clone of the STM32F103 chip named GD32F103. +# There are 2 Mainboard versions out there v0.0.5 and v0.0.6, this config has +# been tested with the v0.0.6 only. It should probably work for v0.0.5 as well +# since there are no different changes in the Anycubic Marlin firmware. +# The LCD is not supported yet (might work, but didn't try yet). +# +# To create the Firmware you need to use the following configuration: +# - Micro-controller: STM32 +# - Processor model: STM32F103 +# - Bootloader offset: 32KiB +# - Communication interface: Serial (on USART1 PA10/PA9) +# +# To install the Firmware rename the klipper bin to `main_board_20xxxxxx.bin` +# and copy it to an SD Card. +# Power off the Printer, insert the SD Card and power it on. +# It should beep several times and the LCD should be stuck on the Splash screen. +# Now you should be able to connect to the Printer, you might need to change +# the mcu/serial setting in this config according to your set up. +# +# If you want to revert the Firmware back to Marlin you simply need to flash it +# with a anycubic firmware through the SD Card + +[stepper_x] +step_pin: PC2 +dir_pin: PB9 +enable_pin: !PC3 +microsteps: 16 +rotation_distance: 40 +endstop_pin: !PA7 +position_min: -3 +position_endstop: -3 +position_max: 245 +homing_speed: 30.0 + +[stepper_y] +step_pin: PB8 +dir_pin: PB7 +enable_pin: !PC13 +microsteps: 16 +rotation_distance: 32 +endstop_pin: !PC5 +position_min: -17 +position_endstop: -17 +position_max: 245 +homing_speed: 30.0 + +[stepper_z] +step_pin: PB6 +dir_pin: !PB5 +enable_pin: !PC14 +microsteps: 16 +rotation_distance: 8 +endstop_pin: PB2 +position_endstop: 0.0 +position_max: 260 +position_min: -3 +homing_speed: 5.0 + +[stepper_z1] +step_pin: PC0 +dir_pin: !PC1 +enable_pin: !PC15 +microsteps: 16 +rotation_distance: 8 +endstop_pin: PC6 + +[extruder] +step_pin: PB4 +dir_pin: !PB3 +enable_pin: !PA15 +microsteps: 16 +rotation_distance: 22.76500 #has to be calibrated by everyone, official document: diameter = 7.25 +gear_ratio: 50:17 +full_steps_per_rotation: 200 +nozzle_diameter: 0.400 +filament_diameter: 1.750 +heater_pin: PA1 +sensor_type: ATC Semitec 104GT-2 +sensor_pin: PC4 +control: pid +pid_kp: 28.937 +pid_ki: 1.295 +pid_kd: 161.688 +min_temp: 0 +max_temp: 260 + +[heater_fan extruder_fan] +pin: PB1 + +[heater_bed] +heater_pin: PA4 +sensor_type: EPCOS 100K B57560G104F +sensor_pin: PB0 +control: pid +pid_kp: 67.648 +pid_ki: 1.044 +pid_kd: 1095.893 +min_temp: 0 +max_temp: 110 + +[fan] +pin: PA0 + +[controller_fan controller_fan] +pin: PA14 +stepper: stepper_x,stepper_y,stepper_z,stepper_z1 + +[probe] +pin: !PB12 +z_offset: 0 +activate_gcode: + probe_reset + +[output_pin BEEPER_PIN] +pin: PB15 +pwm: True +value: 0 +shutdown_value: 0 +cycle_time: 0.001 +scale: 1 + +[output_pin probe_reset_pin] +pin: PB13 + +[output_pin LED] +pin: mcu:PA13 +pwm: False +value: 0 + +[bed_mesh] +mesh_min: 15,15 +mesh_max: 230, 230 + +[filament_switch_sensor runout] +pause_on_runout: True +switch_pin: PA5 + +[mcu] +serial: /dev/ttyUSB0 +restart_method: command + +[safe_z_home] +home_xy_position: -3,-17 +z_hop: 10 + +[printer] +kinematics: cartesian +max_velocity: 300 +max_accel: 3000 +max_z_velocity: 10 +max_z_accel: 100 + +[gcode_macro probe_reset] +gcode: + SET_PIN PIN=probe_reset_pin VALUE=0 + G4 P300 + SET_PIN PIN=probe_reset_pin VALUE=1 + G4 P100 |